Dish washer not heating dishes wet when cycle was completed
Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected! (P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival). Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence. When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?
The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!
Dishes were not getting clean, always had a film on them and dishes didn't dry.
I removed the kick panel at the bottom front of the dishwasher. Then using a flashlight and a cross point screwdriver, I removed the thermostat from about the middle left. It requires a short screwdriver, but not quite as short as a stubby. I unplugged the wires, noting that one of them was a little burnt looking. The burnt looking connector was still okay. I then installed the new one, with the green dot on the thermostat having the slightly burnt looking connector. Then I ran a load of dishes and the dishwasher worked as it was supposed to. It has worked okay twice since then.
1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!
Bottom of Silverware gone,silverwear went to bottom of dishwasher
Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
The door springs were broken and the dorr was very heavy to open and close.
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.
Broken wheels, Caps and Brackets. Couldn't hold dishes or wash right.
Just use a hexagonal driver to remove the Upper rack roller, screw the new ones in, place caps on the rail ends, and pop the new wheel on with some pliers! Simple and fun!
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.