Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven temp was not heating up to desired temp and using an oven thermometer to confirm
moved the range out to access back removed 5 screws from back panel removed 1 screw from thermostat installed new one replaced screws, done in 20 minutes problem solved
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.
It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.
Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.
The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.
I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.
All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.