Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.
Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.
Dishwasher not cleaning dishes, found it not filling with water because hose was ruptured
Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps. installed new hose.
I followed the previous repairers instructions. -Remove the screws around the door panel -Remove the door panel face -disconnect the wires -reconnect wires to the new Latch Assy -tighten the screws and reassemble the door panel.
Original hose needed replacement due to leaking holes
The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit. As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.
I watched the partselectrepair videos for tub gasket, bottom gasket, and splash shield. The instructions were very clear and easy to follow, thank you so much now I have a dishwasher that's good as new.
The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!
Our dishwasher handle was broken and I stumbled upon PartSelect's YouTube video that described how to change the Latch Assembly while looking for a new dishwasher. It looked easy so I thought that I would give it a try. The hardest part of the installation was finding which circuit breaker shut off the dishwasher. That being said, our dishwasher was slightly different from the model shown in the video. When we unscrewed the screws on the inside of the door the top part of our dishwasher did not come off and fall forward as it did in the video. Our control panel was longer and continued beneath the front panel. We could not access the latch assembly until we removed two small screws near the bottom of the dishwasher door and popped the front panel off. Other than that it was exactly as the video showed. EXCELLENT service. I ordered the part and received it the next day. WOW. I would recommend this website to anyone who needs appliance parts.
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
1 Removed 2 screws to remove door panel so as to access back of dispenser. 2 Unplugged 2 color-coded wires attached to dispenser 3 Removed 6 screws attaching the dispenser.
Removed the 6 screws from top section inside door. Pulled control panel from front side of door. Removed two screws holding latch assemly unit and pulled 4 wires from connection. Attached the 4 wires to new door latch assembly and screwed back into place. Replaced the control panel and attached with 6 screws. Couldn't get any easier.Great service Quick delivery.