FAFW4221LW0 Frigidaire Washer - Instructions

Only two screws and it was done,easy repair

Installation of Part # 131-763-202 door lock and switch Assy.

Note that the only reasonable access to the lock and switch Assy is by removing the front of the gasket between the drum and the cabinet. It is also the only necessary access.

This problem is unique to older models. My experience was a bit frustrating but the solution was finally found. While it took me a long time (and extra parts) to figure out the problem, the solution is actually pretty easy.

IF you have an machine with a black striker/catch on the door, the installation is not entirely straightforward, The black striker/catch on the door has an L-shaped lower prong that engages the door latch. This striker/catch will NOT work with the newer door lock. The required striker/catch is part # 134-456-600. It is white, and has a diamond-shaped upper prong.

When you remove the older-style lock (Part # 1231-269-400) that accepts the black striker/catch, you will immediately notice that there are more electrical connections on the new part than on the old. This requires some minor rewiring.

The two connections (Bl/W and w) that go to the latch solenoid are unchanged and attach to the brown solenoid on the new part.

The arrangement of the other connections on the new lock/latch is as follows (numbering is mine)

1 2 3 4 5 6

Terminals 2 and 3 are the “PTC” and must be connected to the red (double) and white wires that are on a special double plug. The plug must be cut off and replaced by regular (F) spade connectors. DO NOT be tempted to insert the double plug into the new lock. Although it fits, it does NOT work.

Connect the two door-lock switch wires (Bk and Bk/R) to terminals 5 and 6.

Note that with the new lock, the machine has to rest a while before the catch is released, the door catch is not released as soon as the door-lock light goes off.

Note also that the actuation of the switch in the door lock is NOT purely mechanical as in the older door lock. Pressing the striker/catch into the lock will NOT close the contacts between terminals 5 and 6. Some magic happens inside the door lock mechanism through the PTC that closes this switch. This same magic is probably responsible for the delay in releasing the door latch. This drove me crazy for a while as I thought the lock and switch Assy was defective.

Super simple, unscrewed the existing screws, removed broken piece, attached piece, screw it in. Done deal!

Removed 2 screws , unplugged the old switch , replaced with new one and secured with screws . Easy !!

Unable to get the door hinge off the machine after 6 years, one screw would not budge and was beginning to strip the head. If you take the door apart while still mounted to the hinge, you must have another person hold the door pieces securely, or you will likely break the tab on the front door piece that fits into the hinge bushing. Don't let that happen! Easy does it, hold it still, unscrew all the screws and gently pop the inside piece away from the outside piece, HOLDING IT SECURELY. Use gloves so you don't get cut, that glass is really sharp. Good idea to use some masking tape and cover the cut edges...I thought of this too late...wish I'd have done it. Lining up the bushings is probably the hardest part while getting the front and back pieces together with the big glass bubble secured, and again, HELD SECURELY by another person. This really was easy, but I wish someone had mentioned whether to take the hinge off or not, unfortunately, I could not. I had to get creative, and the fix was perfect, even if I did initially break the tab that lines up the bushing...I wasn't spending ANOTHER $90 for the teensy tab being broken. It works perfectly with my fix - but it won't if you can't fix that tab! I was glad I didn't have to call a repairman!!!

Ordered a replacement door strike which was easily replaced with Phillips screwdriver. I was very grateful that the part was so easy to find on this website. It was helpful that I had saved my book with model number of washer which allowed me to find the exact part needed. Thanks!!!!

First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.

1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.

This is the second part I have put on it and it still does not work. It is now leaking some also. So tonight I replaced it.

I used a screwdriver to screw on the new door strike. Problem solved!

Removed two screws, installed new piece.

Easy repair, buy shipping took much longer than advertised!

I read other problems, I jumped the gun and purchased the door switch, this was easy to change, but MY machine still had the same issues, however, I found that the filter was plugged, and after I cleaned this out, this fixed my issues and the machine works fine, So I now have a door switch and striker should mine go bad, Hope this helps out

Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!