pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.
First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.
I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company
Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Selector knob for the load no longer engaged when you tried to switch to a different load size
We took off the selector knob that was on the washer and you could tell one of the feet was broken. We then ordered the knob and a number of other items in case it was not just the selector knob. We were lucky because it was only the knob. We pushed the knob into place and it works. We did return the other items. The other items, pressure switch and electronic control board, were suggested by the website in case we had a bigger issue. We ordered all up front so that once we took off the selector knob if we had the other issues we would not need to wait for parts. Thank you for having parts available and sending them in a timely manner and also helping with the return of parts.
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
Watched the repair video on PartSelect website , repair was exactly as they showed on video , grab old agitator at base , give a quick pull and it popped right off , lined up tabs to coupler with new agitator and gave a sharp push down and new agitator snapped right on. Total repair time was approx 5 minutes .
This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again
First I unpluged the unit then I remove the hot and cold water hoses from the back. I removed the torx head screws that hold the control cover at the top of the washer, then I located the water valve. Once I located the water valve I took the 2 phillips head screws that hold it in place out , unpluged the electrical connecters took the water supply hose off. I then removed the old valve and replaced it with a new one.Then I put everything back together. very simple job 10 minutes tops.
Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.
Use flat head screw driver to push in clips that hold on front panel. use plyers to remove hose clamps on motor and remove hoses. use nut driver and remove two screws holding bracket in place. disconnect two wire plugs. Install motor and work above in reverse. very simple 15min job at most.