Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pump Connector Leaking
Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.
The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!
unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
i removed the screw holding the drain pump to the wire that held the pump to the dishwasher frame, i then unscrewed the hose clamps that connected the pump to the drain hose and the other part of the dishwasher i disconnected the wires , put the other pump into place wired it up and now my dishwasher is as good as new .
Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.