Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The detergent cup would not open during wash cycle
I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website
the pump was not working so the dish washer would not drain
Removed the front covers on the bottom of the dish washer. I found it extremely difficult to stretch the belt over the second pulley so I soaked the belt in hot water for a few minutes to soften it. After I soaked the belt it stretched enough for me to work it into both pulleys. Don't forget to apply the grease (supplied with the belt) after the belt is installed.
Space too small to see just where to place belt - Plus the belt had to be put on at the bottom of the dishwasher.
My husband and I both tried to get belt around the pulleys according to directions that came with the belt. The space was just too small to work in. We ended up turning the dishwasher upside down! We could then see what we were doing....My husband finally got the belt on....He did end up with lots of small cuts of his hands from sharp edges. But we were so happy to get it fixed. We had priced new portables dishwashers at six and seven hundred dollars. We were thankful to be able to get the part for our 23 year old dishwasher. It is now working great.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
"The order arrived in relatively short order. However, the installation must have been hilarious to any observer. Imagiine an arthritic septuagenerian getting down on the floor and wallowing about fitting a dish washer belt. Hints: 1. Grasp the pulley on the pump with your left hand from under the discharge hose (more room than over the hose) when fitting the belt to the rear of that pulley. 2. Use a hot pad (not an emroidered & quilted one reserved for company) to protect your L forearm from the frame member on the bottom of the machine. Getting up was worse than getting down, but it works! In dishwasher years it's much older than I am."
based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped