Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not dispense second load of detergent.
Since the bimetal repair kit was not available, I bought the complete detergent cup, gasket, and bimetal switch assembly set. This was still far cheaper than paying for a professional repair. All I had to do after shutting off the power is to remove screws to open up the door (door trim/6 screws & 6 screws on the inner side of door edges to remove outer wall of door). The detergent cup assembly is right there for easy access! I unplugged the 2 electric wire plugs to the bimetal switch (paying attention to which plug goes where for when I reassemble), removed the 6 screws that mount the cup assembly, removed assembly and gasket, cleaned the surfaces, and reassembled with the new assembly. Very, very easy to do and everything works like a charm!
dish cover not rotating to release second pocket of detergent
followed the scematic on the wesbite that i used to i.d. the repair part needed. removed the front door outside cover (8 screws) removed the bi-metal switch (2 screws), did not need to replace the door latch or spring. replaced the switch and the front door cover and ran the dishwasher to test the new switch. worked fine and has been working fine.
I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!
detergent cup would not always open during wash cycle
first I removed the 4 screws that hold the bottom part of the door cover and then removed the 6 bolts with a power screw driver with nut attachment.I then reomved the 2 wires which are color coded and noted which one went where.I removed the old unit and installed the gasget and new detergengent cup,the wires,bolts and door screws.You do not have to remove the screws to the top part of the door.The screws are located inside the door on each side. Took about 20 minutes.
The detergent cup would not dispense during wash cylce
Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.
The detergent holder wouldn't spring open during the wash cycle
First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.
Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.
It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.
I removed front bottom cover,found belt broken. I ordered part online on 10-23-09,part arrived on 10-24-09,amazing. I lossened the two bolts that hold the drive motor to the frame,slipped the new belt on and applied the supplied silicone grease. I then ran the two bolts in with a 3/8 wrench,put the cover back on. Everything works like new now. Great delivery and easy ordering system online. Immediatly called my neighbor and told him about partselect.com
Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.
Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.