Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squeaking noise
Dryer was making a horrible noise. When I took it apart I noticed that the from side dryer bearing was ruined. Ordered the part with the slide bars and replaced...Works great...
Our gas GE "Eterna" King Sized capacity dryer started squeaking one day. I was suprised since the dryer was only a few years old, but assumed some grit had invaded and worn a bearing in the belt tensioner. My wife and I have three kids, so we use the dryer daily. The sound got louder quickly and finally it was so loud I had do something. After unplugging the appliance I took the top off the dryer (two screws in the top of the door jam) and the front off (two screws at the top of each corner) and in doing so saw that the drum bearing, which is just a round plastic "shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse. It would help to have another person assist you.
handle broke on sunday( not the best day to order things). ordered it from this site and had it by tuesday. great service and best price i found on the web. tks
I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks! Let me also say, I only have one good working arm/hand.
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Unplugged dryer, slid away from wall, and rotated 90 degrees. I removed top panel, and front panel, pulling off 2 electrical wires, and disconnecting 1 Molex connector, for the door switch. I turned the front panel around, and leaned up against the dryer drum. I removed the light bulb, then snapped off the remains of the upper bearing, then unsnapped the duct panel assembly. I carefully positioned the duct assembly against the front panel, carefully making sure not to pinch any wires, and pressed into place. I then pushed the bottom of the top bearing into the duct assembly, and pushed the top into place, replacing the bearing wear strips, 2 black, 2 white once bearing is snapped into place. I rewired the door switch, put the bulb back in, screwed the front panel, then top panel back on, rotated back into position, plugged it in, and started dryer. Problem solved!
Watched the video on a different style of dryer so taking apart a bit of a challenge. The old Front Drum Bearing was completely gone on left side and a challenge to pry it off the front dryer panel. replaced felt seal and front drum bearing. noticed that there was 4 places for new bearing slides. the ones i ordered were white and green but did not know why or which one went where as no explanation with packaging. also only ordered one of each and so now had to stop and try and find two more. ! hour later i had brought back a tupperware lid that was thick enough and stated could go to 194 degrees F. i cut out one replacement for green bearing and reused the old white one since it was in good shape from right side of drum bearing. i went back to this website and noticed in the comments section for drum bearing that someone stated the green bearing slides go in at positions 11 and 1 and the white at 10 and 2. they are different materials and having more weight of drum on green now made sense. put machine back together and told neice to keep eyes and ears on dryer thru cycle. she did not even know it was running just in next room.