Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old drum bearingwore out, squeeking like a banchee
Received part in two days. Removed inspection plate by removing two screws. .Drum bearing was right there. With screwdriver removed "c" clip, took out what was left of old bearing. With screwdriver aligned drum, slide new bearing into place. Job was done. Instruction with new part simple and easy to follow.
Removed the front panel,tiped up the top panel ,removed the drum, drive belt,motor and exaust tube assembly. cleaned and vaccumed all lint from every were. Removed motor from fan blade and houseing. Reinstalled moter and pulley that came with the moter and fan blade. reinstalled all of the rest of the parts and plugedin the wires. once all back together pluged into outlet and turned on and prasto works great.
When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!
To perform this repair (please see numerous descriptions on the web for generic belt replacement) I had to rivet two loose parts to the drum in order to reinstall the drum. Specifically, the loose metal disk and hot air shroud at the rear of the drum (near the rear berrings) made it impossible to realign the parts to reinstall the three torx bolts at the rear of the drum during reassembly. These two loose parts are positioned behind the drum (when looking inside the drum) i.e. between the drum and the rear berrings.
It was necessary to align the mounting holes in the drum, disk, and air shroud outside of the dryer itself and then to rivet them in place (making sure the smooth rivet head was INSIDE the drum as to avoid providing a rough edge where the clothes could catch during tumbling). Just press the 3 torx bolts through the holes to establish correct alignment. Be sure to install the rivets ouside of the contact area between the heat shroud and mounting plate. You should see an indented pattern on the heat shroud that you can use as a guide.
It was also helpful to make a black mark on one of the drum mounting holes (inside the drum) and its mate on the berring attachment plate - to help orient you when installing the drum with the 3 torx bolts. It only aligns one way - and making the marks will save you aggravation while your head is in the drum during reassembly. Loud swearing at this point only punishes your ears because, after all, your head is in an acoustically punishing echo chamber - and the echoes make it seem as if the dryer is actually cussing YOU and your incompetence out...
I hope this helps someone else save some time in reinstalling the drum.
One additional pointer: you must remove the lower plate on the rear side of the dryer to wrap the belt around the tensioner pulley and motor drive. The belt wraps, from right to left, first around the motor pulley and then up and to the left around the tensioner pulley. Just place the belt around the motor pulley, and then pull the tensioner pulley toward you and leftward until it clears the belt, then push toward the front of the dryer - and let the tensioner contact the belt on the right side of the tensioner pulley.
And finally, the ribbed side of the belt makes contact with the drum and the motor pulley. The smooth side of the belt is in contact with the tensioner pulley. Good luck, and may the choice words I used during the process be unnecessary for you... for you... for you!
It took more time to figure out how to get the dryer apart than it did to fix it. Unfortunately I ordered the wrong parts the first time but Part Select was very helpful and efficient in helping me get the correct parts. I located the two screws that hold the top onto the machine inside the door frame at the top. Once the top was off, there were two screws that held the front door assembly to the dryer. The old parts (very worn and next to totally gone = none of the slides were remaining) were easy to snap out and the new parts easy to snap in to place. The Spa is happy that the dryer is quiet again and can be run when we have clients waiting. Thanks to you Part Select.
Belt and pulley both broke. Ordered parts; received 2 days later. Took off front and top, positioned belt, replaced pulley and nut. Parts fit perfectly. Reinstalled covers. Ran dryer. Easy fix.
Start Switch stick (plastic thing that pops out) was broken
Removed 6 screws from the back panel and lifted/pushed the metal back panel up. Removed/sliced out the start switch by hand. Replace the new start switch and tightened all screws. Replaced the new selector Knob and it worked like charm.
The plastic door handle on the dryer broke and came off.
I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!
Just followed the installation video. The only issue with the video was that a phillips screwdriver was specified and I actually needed a torx screwdriver.
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.