Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
icemaker quit working when we moved
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
When freezer door end caps & refig door end caps arrived just opened packages inserted end caps onto shelf bar and inserted the complete part into the slots provided on the frig and the freezer door. Needed no tools, just a little common sense. Took less than 1 min for both doors. Any one can do this repair.
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Hard to get started at the corners because it was hard to see the slot.
My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along. That helped us finish the installation. Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator! My newer refrigerator "snaps" shut.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
I disconnected the old defrost heater removing 2 small screws and the electrical connectors, afterward I attached the new part, reconnecting back the electrical connectors and screwing the removed 2 screws.
Repair was not done using th part shipped. We went with the guide of the parts on the refrigerator. It would have helped if we could communicate (email or verbally)( with your parts center to verify the part we were ordering or on how to install it. We could wait for few days for a response. I am still waiating for instructions to return the part. It was a futile effort on both sides.
Your response would have helped tremendously..The picture was not adequate. Your group should be accessible to your customers.
Removed icemaker from freezer, Removed 3 screws from cover plate, and removed screw securing main gear, removed gear. Pulled back cover plate to expose switches and mechanism. Removed screw holding switch to remove switch, and installed new switch. I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install. But it works!
