I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.
Original evaporator fan (31 years old) was making a lot of worn bearing noise
Empty freezer; Remove shelves and ice trays; Unscrew and remove the rear vertical panel; Unscrew and remove fan housing; Unscrew and remove fan from fan housing; Fan blade slides off the motor shaft without tools. Reverse order to reassemble with new fan motor.
I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.
freezer too cold and refrigerator not cold enough because fan not working
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place. Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled. The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower.
I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough. The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws. Cranking out ice like crazy.
First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story. This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.
The icemaker quit making ice and the water started forming on the bottom of the ice bucket.
First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.
I had to order bucket as well. Then I removed 3 screws from bottom of bucket and removed auger parts as a unit put new drive cup in new bucket and re attached auger parts as assyembly and reinstalled in freezer.
Door no longer closed on it's own and would not stay closed all the time
First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set? Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.
