Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer simply stopped running
I looked up the problem on Utube and saw a demo on what three items to check with a volt meter for continuity or resistence on either the start button, the door switch, or the thermal fuse. The first two checked out OK but the fuse was dead, no resistance or ohmns on the voltmeter. I had trouble locating it on my dryer as the Utube site said to pull the rear cabinet off when actually it was under the front panel below the dryer door sitting in an awkward position right on top of the dryer motor. I used 2 flat head screwdrivers to pry open the latches over the panel door that are located about 4 inches in from either end and then used a small right angle screwdriver with a flash light propped against the heating elements (after I removed the cover plate) to see with and to give me more room to loosen just two tiny screws that attached the fuse to the motor. Voila! It works better than before.
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Dryer belt so old it slipped and would not turn drum
Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke! Another bonus is after 10 years I got to remove the softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!