Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
A 2" x 4" section on the bottom of the ice container bucket broke out.
Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.
Icemaker worked sporadically, infrequently, not at all
Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Shut off water supply at the main, drained water from lines, pushed filter in from end of filter then pulled out. Removed the 2 plastic protecting tubes from the inlet and outlet stems. Made sure filter was facing same way as the old one, pushed filter in making sure it was locked, turned water supply on slowly, ran about a gallon of water thru filter. If not done the taste is odd. 5 minute repair.
Coming from the refrigerator, there was an intermittent "clicking noise", occurring about every 30 seconds. The frig. eventually failed .
I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.
removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.
Ice was not dispensing. Examined the ice bin and auger, noted that the plastic ring that holds the auger at the front of the bin was broken all the way around. Pulled out old bin, making sure the ice fill level was raised all the way up, and pushed in the new bin. The new bin filled with ice, which promptly turned into a solid mass of ice because the ice maker was also faulty. I replaced that as well and have not had any issues.
Removed the old filter and took off the water caps and pushed it in place. Then I used a pitcher to clear the air from the line and we are good to go for 6 more months
I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.