Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace igniters
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Oven wouldn't reach temp, gas smell and loud pop when gas would re-ignite,took 45 mins or more to reach 350' from starting temp of 100'
Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.
Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.
I first switched the old burner to a new position and different ignitor wiring. The problem persisted in both places, so I bought a new burner assembly and now the burner lights immediately. Very happy and a very simple replacement.
First I removed the old burner head by twisting it counter clockwise by using wide channel lock pliers. When It completely came off, the burner head had deteriorated so much that it almost came apart. When I took off the 2 wires from the burner head it also easily came apart. The burner-head was in really bad condition. I cleaned the whole area and connected the 2 wires to the new burner head and hand tightened in a clokwise direcrtion. It took 20 minutes to install.
The oven glass shattered when I dropped water in the heated Glass
I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order.. The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!
Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!
Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together. Be patient, it takes a few moments for it to begin heating when you first turn it on. So easy a woman can do it ! I know,(I am one).
I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.
one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!
