Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Crazy codes and not heating the oven properly at desired temp settings
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.
The oven glass shattered when I dropped water in the heated Glass
I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order.. The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!
I got on-line, found your website, put in the required information (model #, brand, part, etc.) and ordered. Before ordering however, I measured, looked at the picture on-line, and compared to the part I needed. It looked right. I ordered, and the parts came in a timely manner. Got an e-mail saying they were ordered, then another e-mail saying they were shipped. Got the parts, installed, they look so good. I'm very pleased. Thanks!
Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.
Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.
The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.
Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.
Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.
Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.
Piece of cake, really.
Total repair time: about 30 minutes, including the mandatory halfway beer break.
