Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher wasn't cleaning properly
I just did the repair just like the video suggests to fix it. I disconnected the power cord, shut off and took apart the water inlet line, and drain line. Unscrewed the top of the washer from the cabinet and pulled out the dishwasher. Tilted the washer to better get to the bottom and took off the connecting wires (red and white.) Unscrewed the brass nuts holding the heating element and removed the element from the machine. Took out the bottom sprayer arm. Replaced the element, replaced the brass nuts and connected the wires back up. Put the sprayer arm back in. Pushed the machine back into place and re-secured the top to the cabinet. Hooked all water, drain, and power lines back up and all was good again.
Original hose needed replacement due to leaking holes
The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit. As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.
Dish washer not heating dishes wet when cycle was completed
Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected! (P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival). Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence. When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
1 Removed 2 screws to remove door panel so as to access back of dispenser. 2 Unplugged 2 color-coded wires attached to dispenser 3 Removed 6 screws attaching the dispenser.
Removed the 6 screws from top section inside door. Pulled control panel from front side of door. Removed two screws holding latch assemly unit and pulled 4 wires from connection. Attached the 4 wires to new door latch assembly and screwed back into place. Replaced the control panel and attached with 6 screws. Couldn't get any easier.Great service Quick delivery.
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!
The door springs were broken and the dorr was very heavy to open and close.
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
