All Installation Instructions for Crosley Range CC35111ACV

element burnt out

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

Parts Used:

Bake Element

richard from KAUKAUNA, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Racks were old

Replace the racks. No special instructions.

Parts Used:

Oven Rack

Sandra M from DISTRICT HTS, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner swith not working properly

removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great

Parts Used:

Range Infinite Burner Switch - 8 Inch

leland from CARTHAGE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

Parts Used:

Door Seal

Mz from COLUMBIA, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original rack had melted plastic on it.

Removed the original rack. Checked dimensions, installed the new rack.

Parts Used:

Oven Rack

Linda from BURBANK, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Large burner was surging indicating infinite switch failed

Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.

Parts Used:

Range Infinite Burner Switch - 8 Inch

John from CENTERVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

could not regulate element

replaced control

Parts Used:

Range Infinite Burner Switch - 8 Inch

Billy from LE ROY, WV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

my first order a small drip bowl

came only I had to order the set again

Parts Used:

Drip Bowl Kit - Light Gray

marie from WATERBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Infinite switch replacement.

I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.

Parts Used:

Infinite Switch - 6 Inch

William from Kerens, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1960's oven door gasket fell apart, actual gasket not available any more

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Parts Used:

Door Seal

Mary from WINCHESTER, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My original back leg broke because the floor is uneven. Had to pull it out several times.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Phyllis from BROWNVILLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My oven door seal had dried rotted

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Parts Used:

Door Seal

Anita from ELKTON, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ELEMENT BURNT OUT

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

Parts Used:

Bake Element

stacy from West Liberty, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The three braces under the coils had weakened and fallen apart

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

Parts Used: