Burner was out but the burner coil worked on onother burner
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
After self cleaning the oven received an error code telling me the sensor was bad.
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly. This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )
oven getting 50 degrees or more, hotter than setting
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory. Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal. Canceled order on panel as Sensor fixed my problem.
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
slide out upper protective sheet metal protector. it is loose and can contirbute to the element failure from door closing.
remove rear element screws,and upper support screws. slide out upper element.
do not cut the wires, they contain mating plug to element. use pliers to pull apart the male-female plug on element wires.
reverse procedure to install, use old extra screws on upper metal protector to prevent loose rubbing on upper element. there are holes for this no drilling required.
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the switch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.