Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bake element took a long time to heat
It was real easy. Removed two screws, pulled the element forward, removed to clip on wires, removed element and put the new element in place, replaced wires and screws, turned it on and up to temp. in no time. great service and quick delivery on getting the part.
Removed burner and tray. Removed burner connector from stove top using screw driver. Removed existing heat shrink and wirenuts. Installed new connector - wire nuts and heat shrink. Used lighter to shrink. Took 20 minutes.
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and screwed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)
Sparks where the heating element plugs into the stovetop
The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked! So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.
my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics
oven heat tempature uneven and would not fully heat up.
Turned off 230 volt breaker to range,connected old wires to new element ,put back into place replaced the two mounting screws. Turned breaker back on and tested range.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.
Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I installed everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.
Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple. P.S. element was delivered very fast!
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
