Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven very slow to lite off
Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! Good luck!
Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.
I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.
ignintion spark was very weak, burners would not light
removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws
Our oven was very slow lighting (would sometimes take over 30 minutes)
The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!
We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday, it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.
My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed the V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!