Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven either would not come to set temperature or took a very long time. Gas would flow to burner for only short times. When burner was lit, flame was often low. There was often the smell of gas.
Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal may not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.
After on-line research i realized the igniter failed.
Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.
First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.
Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.
I replaced the Oven Igniter. With a ohmn meter I checked the resistance on the Igniter and there was nothing there. I figured the module had to see some kind of resistance to turn the gas on. The Oven now works after replacing the Oven Igniter, but the Broiler still will not light. I will check the resistance on the Broiler Igniter and see what is going on there. The Igniter can be checked from the back by removing the back cover panels. The two igniter wires come out through the back of the oven and have heat resistant covering on them. They run into a plastic plug and can be accessed at this point to check the resistance. To remove the Oven Igniter, remove the oven racks, the bottom panels which are held on by screws. The Oven Igniter is attached to the gas rail which is attached to the underside of 2nd panel by two wing nuts.
Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! Good luck!
1. Removed drawer 2.Removed back panel (2 screws). 3. Disconnected power line from old igniter 4. Removed 3 screws holding old igniter. 5. Replaced with new igniter. Works like new.
Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).
I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.
Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You