Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would heat for only a minute, then not re-ignite
Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!
The ignitor would lite, but no gas from the valve, then ignitor would shut off
It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.
It woud begin to heat and dry clothes then it would stop heating before the clothe dried.
Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.
Dryer would heat up at startup but not stay hot for long. Took forever to dry clothes. Started smelling a very slight gas leak about a week before the problem started. I suspect the coils have been going lame for quite some time. The dryer heats up like it was new.
Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.
removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!
flame not staying lit, not getting hot enough to dry clothes
Unplug. Remove door and front panel. Unplug two coils. Remove one screw and loosen other on bracket holding coils in place. Slide off coils and replace ( take note one has terminals up and one down). Reassemble.
First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!
My father and I were deciding on weather or not to purchase a new stove. The stove had always worked well but one of the front burners would not work and the broiler element was cracked in half. I thought I could fix it and save alot of money and not have to purchase a new one. I entered the model # into the search engine from parts select, alot of discontinued parts came up that were unavailable. I then went to search by product and narrowed the selection to brand,size,metal,and category such as electrical. I was given like models that have these parts in common. I was surprised how many parts were available for my stove. I had originaly bought the unit through Montgomery Ward. Admiral, Maytag, and Whirlpool share many of the same parts. From the photos and descriptions I was able to find the correct parts. I purchased a new burner element and a broiler element. Unplug the stove first. The tools needed were a Phillips screwdriver and believe it or not that is it. Two screws held the top of the stove to the main cabinet. After removing these screws from the bottom of the stove top. Note all you have to do to find them is open the door and look under the stove top. The whole stove top swings up and back letting you access the burner elements. Three screws hold the element to the bottom of the stove top. Remove these and note the four electrical wires attached to the burner element. Make sure you mark or notate the location of each wire. Attach the new burner and hook up the wires to it. I put the stove top back down and plugged in the range. The new burner element worked but the switch didn't shut it off. I unplugged the stove and removed the the back plate at the top of the stove. The plate is held on by eight Phillips screws. You only need to take the top back plate off. Don't take the bottom one off. After removing the the plate I could access the switches for each heating element. The left front switch had scorch marks on it, so I knew that it was burned out. Another way is to test the switch with a continuity tester and see if there are any open contacts on the switch. I ordered the switch. It was delivered in two days. I removed the old switch by pulling the knob off the switch and removed one Phillips head screw holding the switch in place. I removed each wire and attached them just as they were attached to the old switch. I ratcheted the switch and plugged the stove in to the outlet and the new burner and switch worked great. I removed the old broiler by taking two Phillips screws out and carefully pulled the old broiler element out. I only pulled the broiler element about four inches from the back of the stove. There are two wires that slide off the broiler element. Remove them but don't let them get pushed back into the holes that they are located in or you will have to take the entire back of the stove off and push them back through there openings. I unfortunately did this and this added time to the repair job. There are two Phillips screws that hold the broiler element holding bar they are located inside the roof of the stove. Remove these screws and slide the old broiler element out. Slide this holder on the new broiler. The holder slides back and fourth on the broiler element so you can position it in the right spot. First attach the electrical connections by sliding on the two wires to the broiler. Push the broiler ends back into there holes and attach them with the two Phillips screws. Next slide the broiler holder on to the broiler element and then position the broiler on the roof of the oven. Attach with the Phillips screws. After doing this I plugged the stove in and turned on the broiler and it works great. There were alot of screws that held the back top plate to the stove and other screws that attached the switch, burner element and broiler element in place, so it would be a good idea to note were these screws are placed. Then there will not be a problem matching
First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.
Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying close attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.
Pulled out AC cord from wall socket first! Removed the dryer door and front panel (2 screws each) Then pulled both wire connectors off 2 coils. Removed hold -down bracket over coils. Replaced both coils and reconnect . No need to replace electronic igniter for gas. The right parts were shipped faster than I expected. Easy job. The Maytag repairman remained unemployed once again!
