Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
element quit working
removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy Donald Carpenter
The repairman that had come had stated that this part is no longer made, but I was able to locate one through PartSelect and was able to replace it with minimal effort.
I removed the three screws that held down the stove glass top surface and had a person hold the stove top up while I removed the two screws which held the autolatch assembly in place. I then swapped the leads from the failed assembly to the new one and replaced the screws which were removed. New assembly tested out fine and oven was able to self-clean again.
I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!
Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.
Switch off the breaker or unplug. The screws were in tight so make sure your philips bite is new so you do not strip. Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove. Connect and cooked up pizza for dinner. Very easy
Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.
I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and removed the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and was about to disconnect the two wires. It was a bit hard to pull out the wires by hand, but I got some WD-40 and pliers and it was easy. Hooked up and replaced and voila. It was done. Saved me a new $1,500 stove. I wish I knew that the lamp only needed to be unscrewed and not the whole unit replaced.
Had to use wd-40 to get the old part loose (oven is over 15 years old) and used pliers to pull apart from the oven. Replaced with the new part and works great. . . Once I used the wd-40 to loosen, it was super easy.
I read up about the repair on the internet and what it entailed, thought I could do it. So followed directions from the internet after looking up Ammana, model number and serial number, and ordered the part from Part Select.com. It arrived two days later, was really impressed with their business handling of it. I paid particular attention to disconnecting the power and pulling the plug out of the wall as double insurance to not getting electrocuted. The Installation was quite simple, just pull the old one out and put the new one in. I took note of how the old one came out, and connected the new one in the same fashion, and it works wonderfully, just heated right up. It was a good experience.
E. G. First we turned off the circuit to the range. Then with a flash light to see we removed the two screws that hold the element in place. We then pulled the element out about 3 inches and disconnected the two wires. . . Then connected the two wires to new element and put the ends back into opening and replaced the two screws that hold the element in place. The hardest part was getting to the back of the oven for an 82 year old and a 94 year old but we got it working again!.
I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.