Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice buildup. The Ice Machine was frosting over. Ice (due to frosting) would block the drop chute.
Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.
Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.
I shut off the water at the shut off valve when I discovered the leak. I started checking on the web for a part and I found PartSelect.com and I couldnt believe there price!! I had checked with a local dealer and it was several dollars cheaper here.Back to the repair i remove the vent cover on the back of the unit about 8 screws and then there was on screw holding the water valve and three water lines to lines use the puch in method and one is screwed on , i simply remove those and reinstalled the new valve with the coresponding lines. in a few minutes i had ice and water out the door good as new!! I also took the time to install a new five yr water filter!! actually this water valve is much quieter than the origianl I am well pleased with PartSelect I will do bussiness with them again!! Thanks Bob
Water Overflowing Ice Tray And Freezing Entire Mechanism Into Solid Block Of Ice
Shut off water supply line to refrigerator, place towel or rag under corner of refrigerator where unit is located (to catch spillage when lines are disconnected). Remove back cover with 1/4" nut driver /loosen inlet line compression nut while unit is still attached(easier to loosen now than when unit is floating around loose)/remove unit from fridge then disconnect line and wires. Reverse process to install. Water lines going to water dispenser&icemaker are marked/wire connections are idiot proof. Check for leaks before pushing fridge back to wall. Thats not idiot proof!
This was a simple repair. I removed the broken bin from the refrigerator and snapped the white plastic handle / humidity control slide off the broken bin and snapped it onto the new bin. I replaced the bin in the refrigerator and loaded it up with veggies. Took all of 5 minutes to make the repair.
I followed the directions provided by Robert of Florida. My contribution is, be aware that the plastic nut on the auger shaft turns to the right to loosen.
Level of difficulty, as far a mechanical skill goes is relatively easy; however, everything in the interior of the freezer (including icemaker) must be removed to get to the defrost thermostat. The defrost heater only needs the racks and back panel removed. It probably took about 45 minutes with a heat gun to melt the ice off of the coils so that I could work on it-need lots of towels/rags to pick up the water.
took back panel off in freezer.unpluged unit then cut wire to sensor tie in new one wire nut them up and taped.on the heater strip took off two screws and unpluged two wires put the new in same way as taking old one off.I am pleased that the parts from part select came as fast as they did I would for sure buy from them again and prices were very fair.Thank you very much for your service.
By reading another customers tip I decided that my problem was the exact same. I had to order the entire motor not just the auger because the motor shaft was stripped. Once you remove the motor, hold the shaft with a pair of vise grips and use a screw driver to turn the auger off clockwise. The threads are reversed. The new auger screws easily onto the new motor counterclockwise and installing back into the fridge was a snap.
Groove for retainer clip on auger nut was broken out.
After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.
I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes. Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble. All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.
I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!
shelf that covers the icemaker broke when we moved
the only thing I had to do was slide the shelf in.. but this website saved me over $50 on the part (I got a price from my local appliance store of $80.00 and 2 weeks to get it)
