Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves. The oven worked like a charm again.
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Lower burner failed to light, broiler running fine
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perhaps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!