Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch). Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper). Remove the racks (wire shelves). Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven.. Gently pull the wires out and disconnect them from the heating element. Now reverse the process. Connect the wires to the new heating element in the same fashion as they came off. Push the wires and heating element back in place and secure with the four screws. Replace the wire racks (shelves). Replace the door (again, this is best accomplished with a helper). Turn the power back on. Run a test of the broiler to make sure the repair was completed properly. voila!
Disconnected power, removed two screws from bracket. Unplugged old element, installed new element and replaced screws in bracket. Restored power and back in business!
Turned power off to oven Unscrewed broiler nuts (total of 4) Pulled Broiler out from back of stove Disconnected wires Reconnected wire Remounted broiler and replaced bolts Turned power back on
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Turned off the oven power at the breaker. Removed the oven door by opening it all the way down. Flip the two metal tabs, one on each side, so the door releases. I used a flathead screwdriver to do it. Close door almost all the way and lift up to remove. Once the door is removed, there are two screws in the back of the oven connected to the heating element. Unscrew both screws. Gently pull out the heating element from the back wall. There are two terminals connected to wire clips holding the wiring in the back. disconnect, both terminals from the wire clips. Be careful not to pull on the wire or pull out from the wall too far. Connect to the new heating element to the same wire clips gently push it back into the wall reattached the two screws, reattached the door and turn on the breaker and test the heating element. I used YouTube to figure out how to disconnect and reconnect the door so that is an option.
While on self clean, the bake element began to burn
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I plugged in the new element and proceeded to clean the oven which is what I was doing when the problem occured.
Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.
I ordered a replacement glass from PartSelect and after i received the glass, I removed the oven door and placed it on a sturdy table. Then i removed the screws around the outer frame and lifted the door apart. I then cleaned out the remaining glass shreds from the frame and placed the new glass into position in the frame. I then replaced the screws back into the outer frame and placed the door back onto the oven.
Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".