Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.
First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.
the broiler would light once in awhile and it appeared that the igniter was working. But it wouldn't let enough current through to open the gas valve. The nuts holding it on broke off but drilling them out and replacing with two sheet metal screws worked ok. Don't know how that will hold up to the heat though. The wiring was easy to connect ( wire nuts) but the lead wires from the stove are not that long so all the operation had to be done way in the back of the oven enclosure.
After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.
The right hinge was broken and the door would not close properly.
I removed the door by pulling up and away from the hinges. I then removed the drawer. I unhooked the tension spring by hand and noted the opening. I then removed the three screws on the hinge assembly, removed the ole part, and replaced it with the new one. I replaced the tension spring and slid the door back on to the hinges. I did it all in less than 10 minutes.
The plastic wheel glide that the hinge runs back and forth on was worn off on one side so it was grinding and binding. Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides). Take out three screws w/ a hex head nut driver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . ) It was like drinking juice
Replace 4 White Burner Dishes ,4 Grey Burner Grates And Caps. With Black.
There were 3 ? Types of black burner dishes and 3 types of burner caps. The information I collected did not hint about the different sizes. We sent back 2 caps for the proper ones. Meantime 3 of the dishes were on backorder. I installed the one dish I had. Later the 3 backorder dishes arrived. I began to install them when I discovered I needeed more than one size. I am a retired aerospace engineer. I had to use my file and hammer to fit experiences to make up for my parts ordering deficiency. The new dishes, mounting holes, were different than the one I had previously installed . So in order not to return them and wait an additional few weeks , I filed the mounting holes sufficient to be able to mount them. Then I put the next part on and discovered that it did not fit the new location of the igniter . I filed the approx 1/2" dia hole from round to a "d"configuration on 3 parts , that allowed the igniter to function in two of the new locations . The fourth and smallest burner required an additional 1/4" spacer to move the gas supply riser closer tothe igniter. The burners are all working as new. No fire hazards. My wife does not know the goofs I made. I had to use some inventive methods and I'm still her hero. I would caution all di it yourself people to become very familiar with the parts they need. They may all look the same to the novice but there are slight differences that should require replacement and could take away your hero status.
Very easy job. Removed the 3 screws from the oven body, and slid the hinge out of the door. Slid in the new hinge, replaced the screws, and it was done. Very easy, wish I had done it sooner. Finding the part was easy, using the parts diagram. Rep was nice and confirmed the right part. Shipping was fast, and price was reasonable.
hinge became bent - door unable to open or close properly
The video accompanying the part was very beneficial, making the repair easy and quick. Your online site was concise and organized. The product was easily identified and ordering was clear and secure. From a person with no ability to fix anything, thank you for helping to solve a problem in an manageable and comfortable way. A very satisfied customer.
Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.
Oven Door would not open all the way, due to broken hinges.
I utilized the you tube video installation for instruction. The video was clear and easy to follow along. I was able to pull off the door and replace the the right and left hinges within 10 minutes. The videos made it very simple! Thank you
