Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven door would not open all the way
After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.
hinge on oven door was broken, so oven wouldn't shut
Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.
Really easy. 1) Pulled up on oven door and removed it. 2) Removed lower drawer to access springs. 3) Pay attention to which hole the springs are attached under the oven. 4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine. 5) Unscrew 3 screws of old hinge assembly. 6) Reverse process when placing new assembly in place.
Oven door hinge would not allow door to open completely
removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.
first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.
I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.
Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.
Over door would not open fully; light was always on
Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.
Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.
Pulled out bottom drawer and showed my 13 yr old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.
Followed the excellent removal and installation video by PartSelect. Also the diagram was excellent allowing me to purchase the correct hinge the first time. Fast shipping.
REMOVED DOOR TO OVEN REMOVED HINGE [3 SCREWS] REMOVED BOTTOM DRAW UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE PULL OUT DEFECTIVE HINGE REPLACE WITH NEW HINGE AND SCREWS REHOOK SPRING TO HINGE & REPLACE DOOR COMPLETE
Replaced old ignition module with new module from parts select. The most important tip was to label each lead before removing from old ignition module.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.