Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
ignitor failed to ignite gas or would fail to after first ignition.
Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.
I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit. OK, so much for the intro.
I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer. Thank you so very much. Dr Robert E McGinnis
Gas Dryer Runs With Heat for Less Than 5 minutes, Timer Won't Advance in Autodry
My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!
I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.
Dryer was noisey for about 2 years. Repeated greasing of the wheels only resulted in it squeeling again after 6 months or so
Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.
i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks
Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.
Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.
My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!
Found on your site the top two causes of a Dryer not getting hot enough and ordered those parts ( which were delivered quickly).Removed the top two screws that hold the front of the dryer that gives access to the coils and flame sensor assembly after lifting up the top.It took more time to clean up all the lint than to replace the parts.Dryer works great!
Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)