Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dryer squeeking while in use
unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.
the idler pulley was screaming for years on this thing finally it gave up
the repair was easy enough, the idler pulley and bracket was 2 screws to access and one bolt to remove. the thing that amazed me was that Parts Select even had the items we needed, the lint trap was trashed for years as well and I'd looked for it a few times but never found it, When we found Parts Select we found every thing the old beast needed. Its much quieter around here now! that sucker used to howl!
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.
Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness. You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum. Remove the drive belt Remove the drum. You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back. Re-install the parts. I used bearing grease to make it run smoother Attach the new shaft to the drum and reinstall the drum (its best done with help)
Re install everything back again. And you are done
I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.
First I removed two screws holding a bracket that keeps the two ignition coils in place and removed the wires to the two coils. I replaced the old coils with the new coils, re-attached the wires and re-secured the bracket. I also replace the door catch simply using a flat head screw driver to remove the broken catch and pushed in the new catch. The Lint Screen is a simple replacement requiring no tools.
The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.
After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy. I also noted that the new part was of a better design than the original. It should not need further attention.
My dryer would light but when it called for more heat it would not light.
lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.
the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!
first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new
removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!
I've replaced the rear plastic bearing on this dryer twice, so I am familiar with taking the unit apart. After replacing the bearing in December, the machine still made noise (which had been masked by how loud the bearing was). The belt didn't look so great and it's 13 years old, so I ordered one and a new idler pulley assembly.
First, I disconnected the power and pulled it out for access. Using a large blade screwdriver, popped the cover open from the two clips in front. Be sure to support the top cover when you open it on the tabs or they will bend - I propped it against the wall. I disconnected the two wires that go to the door switch, and then removed the two screws that hold the front panel and door in place and lifted/opened that and removed the front panel and set it aside.
Next, I removed the back access grill (2 screws) and popped the belt off the idler by relieving the tension on the belt. Using a 10mm socket, I removed the idler pivot bolt and idler arm assembly. I installed the new idler arm assembly in its place and reattached the spring.
Moving to the front of the dryer, I lifted the drum off the blower housing on which it was resting and took off the belt through the front of the dryer. I then replaced the belt in reverse. Back through the access panel on the rear, I put the new belt on the motor and idler.
Be sure to check that there are no flips in the belt. I rotate the drum by hand a couple of revolutions to be certain.
I then reinstalled the front cover and door, reconnected the door switch, replaced the access panel and put the cover back down, popping the clips into place.
Put the dryer back in place, reconnected the exhaust and plugged it in. Voila - quiet dryer.
As an aside, I also took the time to clean the lint out of the blower and exhaust with a vacuum cleaner hose.
I unplugged the dryer. Undid the top by taking out 2 screws and mounts on each side of the back. There were two screws in the front panel that had to be removed. One on each side. Then I took the two wires off the killer switch on the door. Marking which was top and which was bottom. Then I removed the front panel. Then I undid the drum which had 3 screws in. I took out the drum to find the problem. I replaced the drum putting the belt on. Then I took off the back panel at the bottom of the dryer to get at the idler arm. Took off the spring and unhooked the arm. I put the new arm on and replaced the spring. I then put the belt on to the pulley and closed up the back panel. I put back the front panel. I put the top back on. I plugged it back in and turned it on and it worked!
remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..