Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice Guide tab was broken
Detached the broken ice guide by expandong the opening bewteen the tabs with my hands. Installed the new ice guide and pressed into place. Took about 3 minutes.
took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.
I cut strips from the old slides, super glued them onto the new slides as stiffening where the old slides had broken. This was the 4th set of slides I had installed, a real Whirlpool design fault! I then sild the new pieces into the clips, and away we go!!
First I removed the drawer from the tracks. Second I took the whole shelf out and removed the track from it (it just slides in and out of place). Next I went to my computer and pulled up www.partselect.com found my model number,which was very easy, then ordered my part. In about three days my part arrived. I went to the fridge and slid the piece in. I put the drawer back in and checked for proper operation. It worked like new. Last I closed the door and I was done. Very simple job done with a great quality part.
1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.
1. Put pieces of wood under door to support it. 2. Unscrew three screws holding door hinge. 3. Disconnect water line. 4. Unscrew screw holding each cam. One to door and one to hinge. 5 Replace cams. 6. Retrieve plate with threaded holes behind frame that the hinge attaches to. 7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws. 8. Replace all three hinge screws. 9. Connect water line fitting. 10. Remove wood for door support. 11. Check door for smooth movement and strong pressure when closed.
Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.
my drum was broken and would not put ice down to be used
I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me. I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!! The PartSelect service is great!
This was very easy to install. Part Select had very fast shipping and reasonable prices. I love this website they have everything you need for your appliance. My ice door was very easy to install. I popped it into the grooves on the ice maker. It took about 30 seconds. THANKS PART SELECT YOU ARE GREAT!!!!!! :-)
door would not close automatically and replaced torn gasket.
removed door took out single bolt pried out cam put new one in returned bolt rehung door. 15 minutes
pulled old gasket out cleaned area where gasket was and lube edge of new gasket with vaseline starting at top slide gasket in then sides last was bottom which was hardest. 20 minutes
Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.
Refrigerator door on a side by side unit would not stay closed.
First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit. Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!