66515972990 Kenmore Dishwasher - Instructions

I unscrewed the wash arm tube from the agitator, and then unhooked the plastice holders that held the arm tube, pulling those parts out of the dishwasher. I took the new (one piece!) wash arm tube in hand and then realized that I would have to cut the plastic holder in half because there was no way to get the new (1 piece) arm tube through the plastic holder. I cut the plastic holder in half, fit it around the arm tube, and super glued the holder back together, allowing it to dry for several hours just to be safe. After that, I simply screwed the entire thing back on, and we were good to go. It could not have been easier, except for the unexpectedness of have to cut the plastic holder. Saved us probably at least $100 worth of service call and parts.

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

Install too less that a minute. Fit perfectly.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.

1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time

My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

The part arrived much sooner than i was ready for. with a square allen wrench I was able to install the tube in no time.

No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.

I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.