Models > 66515637000 > Instructions

66515637000 Kenmore Dishwasher - Instructions

All Instructions for the 66515637000
106 - 120 of 428
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Parts Used:
Drain and Wash Impeller Kit
  • Robert from Sherwood, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The coating on the upper rack had rust coming through.
Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.
Parts Used:
Upper Dishrack with Middle Arm and Tube
  • Ernie from Salinas, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Parts Used:
Dishwasher Door Gasket - Gray
  • Gary from Winnemucca, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
had to replace nut that held on the bottom sprayer and replace the water inlet tube
I had already removed the old parts so when the new parts arrived, I just attached the water inlet tube holder and put the nut on the top of the sprayer assembly and it was good to go!!!! I ordered the parts one day before 3:00 and they were delivered the next day!!!! Unbelievable service!!!! Thanks and I am a very satisfied customer!!!!

Julie Welty
Parts Used:
Lower Sprayarm Nut Water Inlet Tube Holder
  • Julie from Christiansburg, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Parts Used:
Dishwasher Door Gasket - Gray
  • Jonathan from Henderson, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Parts Used:
Lower Dishrack
  • Richard from Middletown, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water coming out of the washer flooding the floor
I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.
Parts Used:
Wash Arm Bearing Ring Lower Sprayarm Seal
  • robert from cold spring harbor, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Parts Used:
Dishwasher Door Gasket - Gray
  • Tim from Lock Haven, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer arm wound rotate, bearing was worn.
required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.
Parts Used:
Lower Sprayarm Seal
  • james from encinitas, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes would'nt come clean or dry from torn boot
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Parts Used:
Rubber Washer
  • David from Sallisaw, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original lower dish rack was falling apart.
Took out old rack, put in new one. Part arrived on time and was an exact match to the original.
Parts Used:
Lower Dishrack
  • Chris from La Center, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Parts Used:
Lower Dishrack
  • Donna from Hicksville, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
Parts Used:
Rinse Aid Cap
  • Jose from Coolidge, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher not draining
Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.
Parts Used:
Drain and Wash Impeller Kit
  • Lloyd from Clifton, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower spray arm nut
Open the dishwasher door and remove the lower dish rack.
The spray arm nut had broken off and the spray arm was wobbly.
Removed the spray arm. The threads of the nut had broken off inside the arm. I used three 1/4 inch bolts and inserted them together inside the threaded part of nut and turned counterclockwise. The threaded section came out.
Once the new nut arrived, I replaced the spray arm in the dishwasher and screwed the new nut clockwise in the center of the arm. That's it!
Parts Used:
Lower Sprayarm Nut
  • Michele from THOMPSON, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66515637000
106 - 120 of 428