Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door spring broke-Door falls down
Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.
1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.
Motor starting making a terrible racket after installation 15 months earlier
Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out. All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.
disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.
Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.
Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line. reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
after all I read about the problems with Kitchenaid I figured it was the solenoid thats part of the soap dispenser. I took out all the screws on the door...2 long ones are on outer top...seperated it...took out all the screws on dispencer ring...replaced it...pluged it in and put the door back on. we ran it thru a cycle and the door now opens and makes lil soap bubbles.....another job well done by Hank in action! all the parts in door are easy to replace....
LLeaking at bottom of door -Lower part of inlet damaged
REMEMBER TO SHUT OFF POWER _ Had to remove the screws using TORX driver on the inside door edge-- then came the hard part -- the foam insulation is glued to the inner door and the outer cover- I was able to finally separate the cover leaving the foam on the inner door. Then had to break off the foam insulation on the lower third of the door up from the bottom. I then had access to the screws holding the air inlet to the door. The screws are located so you can't get a straight shot at them and it is very difficult to get at them. These screws are hex head metric and very small. When they are removed the old air inlet will come right off. Take the new one and duct tape it in place inside the door and replace the screws. I recommend doing the outer ones first and since they are the easiest to get started, then you can fight the others a little easier. After the screws are replaced and tightened replace the lower half of the insulating foam by duct taping it to the foam that remained on the inner door. Then replace the outer cover and secure with the TORX screws. This was a time consuming and tough repair. I don't recommend it to a novice.