Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher stopped filling
based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.
Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.
I watched a you tube video which was referred by part select. This was helpful.
I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..
It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.
I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.
front track stop broke on both sides of the upper tray
Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb
Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.
Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!