Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher Not Draining
The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.
The old filter was warped, allowing food into the sprayer system
Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.
PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.
PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part. Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
1. Remove the top rack 2. Take a screwdriver and pry off back plastic stop at end of track 3. Slide track off, then slide new track on 4. Take the plastic back stop originally pried off of old track and snap into new track 5. Open plastic stop at front of track 6. Replace top rack. 7. Close plastic stop at from of track 8. Good to go!
I'm not sure what my project wasm... is the kind that you're interested in. But Ni do have something to say about the product I got from you!
I ordered from you the address cleaner for my Kitchen Aid Dishwasher. I was hesitant about ordering it because, in my experience, these tyo e products are a waste of money and never perform to a level of expectation! But the washer is new and nice and I want to take care of it so in ordered the cleaner. I popped the little pellet in where the detergent pods go. Vli send the door pressed "normal wash" button, shut the door and forgot about it. I forgot about it until I opened the door to put in dishes, ... And BOY!! The inside of the washer was shining so bright I had to put on my sun glasses!! It would have been difficult to not notice how clean the inside of my machine was! No kidding... I was really impressed... in faction glad I got this request for feedback... because I was wondering how to let you j now what a great product this stuff is!
Dishwaster would not reliably start. Just blue flashing light
Removing the door was straightforward. However, when the door panel was removed, I grabbed the door and my finger touched and pressed on something on the right side. This is an optical collector which focuses 3 lights (red, blue, green) into a visible slot. After I reinstalled the door, the lights were not visible. I had to disassemble the door a few times and bend this optical collector into the right position. Basically, I bent the collector into the door, so I needed to bend the collector away from the door. And now, everything is fine.
researched whirlpool and online resources for NO WATER IN DISHWASHER
Thanks to all the people who video their repairs and such. Found the part number from whirlpool online resource then ask you tube for video of anyone who had this issue with this part and video taped their repair. Found video then went online to see where can I purchase this part. I chose Part Select. The part came in within a few days. Went back to video and watched as I replaced the part. Not one issue came up. If only all issues in life could be solved so easily.
1) Remove (2) dishwasher cabinetry (located on top or side) cap and screws. 2) Pull dishwasher out just far enough to access wheel tub assembly. 3) Remove old, clean area and replace with new. “Refer to several videos buy goggling part number”.
Dishwasher does not finish its cycle. The sanitizer light flashes red and there is soapy water left in the dishwasher.
I replaced the thermostat (part # PS11750035) along with the heating element (part # PS9494999) and the turbidity sensor (part # PS11757214). I also checked the filter (part # PS11759673) and it was very clean with no holes. The dishwasher still has water and soap suds standing in dishwasher after I ran it through different cycles. Also, when I run the sanitize cycle the sanitize light flashes red at the end. It doesn’t appear to completely filling with water. Also my hot water temperature is 130 degrees after running for 1 minute. I am at a loss! Any suggestions?