Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain. I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring. The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
After I finally got the right parts and installed them I discovered that even though I had bought the OEM part for my dishwasher it not only didn't fit but prevented me from even getting the upper rack back in the dishwasher. The dishwasher won't work with out the upper rack properly in place. Every part store I looked at offered the same part for my dishwasher so obviously Whirlpool made a huge mistake. Since it's not possible to get the old parts back on (one of them was broken anyway which is what started all of this) I had to buy a new dishwasher. I did contact Whirlpool by email but got no response. If you own a Whirlpool dishwasher be very cautious buying any replacement parts.