Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top rack broke
I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
The replacement kit came with no instructions in the box, so I found the instructional video online. This video pointed me in the right direction so I could take it the rest of the way myself.
Here is the link to the instructional video i used https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm
Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.
This was a very cost effective repair instead of replacing the entire rack assembly.
NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Disconnected the water hose entering and one electrical plug alone with one screw that holds the valve to the machine. Replaced the old with the new and it worked.
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws. 2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out. 3. Unplug electricity 4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines 5. crescent wrench to unscrew the plastic screws in back 6. Disconnect two wires going to element 7. Replace element... reverse steps 8. Not too bad at all 9. Part Select is Awesome !!!!
First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.
heater showing signs that it was going to fail soon
removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..
Heating element went out, dishwasher wouldn't work
I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!