Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
WAITING ON PART
Still waiting for your parts. over two weeks to get part which was a hinge for something, I don't know what, but not my dryer seal. You said you would refund shipping and wrong part and charge me for a new order. End result was I got charged extra shipping for your mistake. The part still is MIA and it has been 5 weeks since I originally ordered. Will never do business with you again.
It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
First unplug dryer... very important. You have to identify the appropriate size socket wrench and locate all necessary screws to remove top panel of dryer and front panel. Locate belt drive. Remove old belt , replacing it with new belt attaching belt to dryer drum . Remove back panel of dryer to better reach and adjust belt onto tension wheels. Put dyer back together. YouTube gives you an idea of how to properly change a belt on dryer
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
The shaft of the previous nob had cracked and even super glue would not hold it together. The dryer timer could no longer be set without it. Slipped it off and slipped on the new one and it worked perfectly.
Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.
Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!
I removed the 2 screws and lock assemblies from both sides on the back. Then i removed 4 screws (two from each side) on the control panel and lifted that up as i tipped the cover forward to disconnect the wires from the door switch. I found the wiring diagram inside the control panel cover, which included a belt routing diagram (very helpful, being the belt was laying in the bottom. I then removed 3 torx srews holding the drum to the bearing, and removed the drum. Let the fun begin! i proceded to put the belt onto the motor pulley and around the tensioner. i needed some help from my wife to set the drum back in as i held the belt up around it. once the drum was back in, i found the beld had fallen away from the tensioner. I lifted the front of the drum up just enough to get both arms below it and move the tensioner back to slip the belt over it correctly. With the new belt on i started to put the screws back in the drum. This got very frustrating, as you have to correctly line up all the holes again, while holding the drum in the correct angle to start the screws. this was the hardest part, not physically, but wears on a person's nerves quickly! Once all the screws were in and tight, i took a deep sigh of relief before i tipped the front cover up just enought to get the wires hooked back up for the door. I turned the unit on to verify the repair before re-assembly. Yep! works again, for well under $20.00! Thanks PartSelect!
Open top by removing 4 phillips head screws above opened door, pop top up. Remove rear access panel, remove belt from drive & tension pully. Loosen top front screws, remove front panel to gain access to remove drum. After drum removed, I realized why rear bearing went bad- two front guides were worn causing rear bearing to angle and wear out. Replaced front pads, buttoned her up and now quite as new. Also replaced drive belt while in there.
First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.
Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.
Remove the bottom cover of dryer to look at the motor, see belt hanging remove broken belt. Remove screws from the top and front, slide belt over drum put small piece of tape to hole belt in place replace screws go back to the rear pull belt over the motor pulley close back panel
