5MSF25N4BA00 Refrigerator - Instructions

Removed the door, laid the door on its side, and pulled the worn part from the door. Inserted the new part, reattached the door, and it works like a charm. The parts diagram online was very helpful. I ended up purchasing a part I didn't need in case an unidentified washer came with it, but I didn't need it. No big deal.

Ordered the part from PartSelect, received it in 2 days and changed out drawers. Very simple and easy.

Part arrived about 4 days after I ordered it. It was in perfect condition and just as described in the picture. Everything was great and a real pleasurable experience.
I will use your firm again in a heartbeat.
Gary N. Smith

Opened the box, took out the new crisper, washed it, removed the old crisper, transfered the veggies to the new crisper, inserted the new crisper, closed refrigerator door! Threw away the old crisper. Done!

I searched the internet to find the best deal. When I came upon Part Select, I was amazed at how easy it was to find the part I needed.

That was the last site I looked at. I ordered my part, because it was so easy and inexpensive.

My crisper pan arrive in a few days and all I had to do was put it in my fridge!

Thank you!

This install was simple and fast. I ordered the drawers from PartSelect.com and received them in less than a week! Switching them over and putting them in was quick and easy. THANKS to a great experience I plan on ordering from PartsSelect whenever I have any future appliance troubles!

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

Removed broken drawer and inserted replacement.
The first replacement door I received was itself broken. A replacement was promptly sent.

Removed the door and replaced the lower door cam. Old lower door cam was completly stripped. Insatalled new one and door sealed again! Yay!

pulled out the old snack pan and slid the new snack pan in.

They just slid right in

I installed a Ice Door Kit. It works Great Now!

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

We got the new drawer and it fit perfectly and look identical to our old drawer.

Ordered replacement crisper drawer on Friday and completely surprised when it was delivered on Saturday. Talk about fast service!