Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burnt brushes
The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!
Damaged gears in both machines. Been setting around for a few years broken. Gears broke way too soon.
Simply removed damaged gears. Very simple to do. Ordered gears. Replaced gears. Both working well ( so far. ) Machines are easy to dismantle. Just be sure to put the screws back in the holes you took them out of when dismantling...no lost screws. On the smaller model, took pictures of the wire positions to be sure they were replaced in the proper order. Larger model had no wires to remove.
The mixer would not spin so I assumed it was a bad worm gear
I watched a video on how to replace the worm gear. When I opened the mixer I noticed a small screw laying in the grease. I removed as much grease as I could and could not find anywhere that the screw would have come from. All the gears turned and looked fine so I replaced the grease put the mixer back together and it worked fine. I am thinking the small screw must have somehow fallen into the mixer when manufactured. So proud of my 70 year old self for getting the job done.
Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!
First i went to the Kitchen Aid web site and found a video on how to take a part the mixer. Followed the instructions from the video and it was very easy. The grease in the machine was black so i cleaned it out of the transmission and repack it with hi-heat wheel bearing grease that i got from a auto parts store it took about a 1/2 lb. then put the gasket in and back together and put the o-ring on. Have run for awhile and it is ok. Want to say that these are very well built machine.
I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.
I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
The mixer would not operate so I took out the brushes. Work afterwards but was a little noisy so, considering the advanced age of the machine and after doing research, I decided to replace the worm gear and bracket.
I followed the instructional video linked to my email order confirmation. Partselect provided one of the best how-to videos I've ever seen. With the right tools, a little patience and the video, I had an outstanding repair experience.