Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
End cap pin broken
The end cap is a very easy job to remove. Removed the three screws that hold the end cap in place using a 1/4 drive socket. Removed sliding rail which is affix to end cap to be reused with new end cap. Installed new end cap with the three screws and your done very easy. What made the job possible was the ability to identify the part from the PartsSelect.com web site which has excellent parts identification catalog.
Door was not closing with any positive feel and would often pop open when left door was shut.
Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.
Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.
You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.
If it wasn't for that minor slowdown it would be a five minute job.
Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.
broke tab that holds pantry lid; something fell on the pantry lid and cracked the clear section of lid
The parts arrived VERY quickly.Replacement was extremely easy even though the right side end cap has the temperature adjustment it only took 15-20 minutes.
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Our refrigerator was too cold as the thermistor seems to have gone
It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.) I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold) circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end) Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
the crisper cover which covers both crispers broke in a million pieces as i was cleaning it in my sink
well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did. the trick was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!
Removed the old gasket and made sure we put the new one in the same way. A wooden mixing spoon was the best tool for pushing the gasket into the track without hurting it. We used the back of the spoon and it went right in with no problem.
Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job