Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water would not dispense and fridge/freezer began to warm
The defrost circut stopped working which caused the coils to frost over stopping the blower and freezing the water line. Take everything out of the freezer, remove lower back pannel held in by around 8 screws inside the freezer. The thermostat was attached to the upper right coil. It clips on to the coil. Wires attach to the fan and defrost heater. A pair of wires runs out through a hole. These wires are to measure thermostat. It will read 0 ohms when frozen. Rremove and replace the thermostat. The defrost heater should read around 25 ohms. Remove the bottom grill. It pops off. The box in the middle houses the defrost timer. Remove the 2 screws holding the box to the chasis and then remove the defrost timer screws... Before buttoning everythigng up, plug the fridge in to the power and wait for about an hour. The fan in the freezer just above the coils should be running and circulating cool air through the fridge and freezer. Depending on how long your freezer was unplugged, the water should be thawed enough to dispense water again.
1- Ice Maker Stopped working, 2- Kick Plate Grille clips broke off second year of use, 3- bottom cam broke first year of use
First I removed the three screws that held the element in place. I had a problem disconnecting the plug from the ice maker, but using a small screw driver and pushing in the slot to release the plug finally worked. It took about ten minutes to get the plug out of the old ice maker.
One manufacturer error was, not making the electrical wires a little longer to access the ice maker plug better.
This is the second ice maker I have installed in the freezer since 2004 and it is rather easy once the plug was removed.
I then plugged in the new unit, reinstalled the three screws, pulled off the cover and arm from the old unit, and put them onto the new installed unit, and it was ready to work.
The kick plate grille took five minutes to install.
The door closure cam kit was installed in fifteen minutes.
Everything went in really easy, except for the plug disconnection from the old ice maker.
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but the part was here in less than 2 days. Pretty awesome little company.
Remove two screws from top door hinge. Remove door from unit Remove old broken plastic cam 1 screw Replace new door cam tighten 1 screw Reinstall door and top hinge screws.
Refrig began to trip the GFI circuit in the garage. When plugged into a house interior circuit the lights and fan ran but no cooling in either the freezer or frig.
First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!
Removed the door by taking 3 screws out of the top and lifting straight up, then replaced with the new parts and very easily replaced the door, worked ike a charm, if i didn't know any better it was like factory new
The door made a loud noise on opening and closing.
Emptied the door. Removed the door, top bolts first. Lifted out the door. Installed new cam at the bottom. Set the door back in place. Bolted the top hinge back on. Smooth!
The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.
inserted a knife between the switch and the plastic interior in order to pop the switch out. then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull end) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.
