Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tub leaning on one side
Changing the springs was a ...snap. The more delicate task was to figure out how to get to them; for this model, the back panel comes off (after removing 3 screws, the drain hose and drain hose plastic coupler, removing the 2 screws holding the control panel, pivoting the control panel and finally removing two spring clips. Also, the plastic water diverter takes a little bit of patience to be unhooked from its slots in the back panel as it will not slide out with the back panel. With the back panel off, the entire "shell" can be removed, exposing the guts. I twisted the tub to release the tension in the suspension springs and replaced them, one by one. Finally, the counterweight spring. I also lubed the support pads to allow for a "friendlier" leveling. Re-assemble, replace the old and cracked water supply hoses, and time for a beer and my girlfriend's obligatory OOOOHs and AAAAHs... All in all (cleanup and test included..) about one hour.
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring. If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Washer basket off-center and wobbling during spin cycle
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Broken water inlet syphon combined with missing feet was causing water to spill out of the washer
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.
the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism. Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires. The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Washer would not start adjutating unless I opened and closed the lid a few times.
Unplugged the main power. Removed the 2 screws in the back and top of the control panel. Pulled control panel forward and tipped towards me to remove from top of washer. Removed the ground wire screw with a socket/ratchet. Removed the switch by pressing the tap inwards. The tab was brittle and broke. Replaced the switch, ground wire with screw and the control panel. I notice that the 2 screws which secure the switch lever/hinge to the lid were loose. These 2 loose screws were actually the problem in the first place. The loose lever was not making good contact with the switch. I think the switch was actually fine but since I broke the tab on the switch I needed to replace it anyhow. Plugged in power cord and washed a load.
Spider coupling between motor and transmission broken
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Washer was not filling with water to proper level (was filling some, not enough)
Ordered part PS3408149 from partselect.com. Lifted Washer control panel with putty knife. Removed hinges (regular screwdriver, used as a crowbar rather than screwdriver) holding control panel to washer body. Moved washer body panel out of the way, and reviewed level sensor/level selector switch. Take handle off front of selector switch. Twist selector switch off from inside (90 degree turn till square inset lines up withsquare hole, then it will come out). Insert new selector switch. Remove old tubing. Fish new tubing through where old tubing was. Cut off extra tubing, then push tubing onto selector switch and tub basin (where old tubing was). Put washer back together. Done. Worked perfectly.