Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Nut Screw Plastic Housing Split that stabilizes attachments on top side of machine
I removed the old screw with a hand tool to avoid injuring my hand. I then used my hand to install the new screw. Piece of cake. Ordering from Part Select was was a breeze. The only minor issue was the part cost $4.33 and shipping was $7.25.
Unscrewed stainless steel Kitchenaid band, removed screws holding down the main housing to get to the speed control panel. Removed two screws from to release the speed control panel, replaced the panel with new part, and replaced all the screws to the main housing, and stainless steel band and it worked like new. So easy, and it only took about 15 minutes to repair.
1) Unplug power cord from outlet. 2) Remove #2 Phillips screw from metal band at the back of the mixer. 3) Remove band and set aside. 4) Remove 4 #2 Phillips screws that connect top of mixer housing with bottom. 5) Gently pry up on top housing to remove. 6) Remove two screws hold original speed board in place. 7) Old board and new board may have board components in different locations. 8) Lugs are marked Motor 1, Motor 2, Line 1 and Line 2. 9) One at a time move a lead from old board to new, making certain you match the leads up to the printing on the board. e.g.; Motor 1 must go to Motor 1. 10) When all leads are moved install new board with the two screws. 11) Put top back on and install four screws. 12) Clean and install stainless steel band. 13) Plug in and bump start to check for proper operation.
Cracked gear housing, Broken Bearing and a couple things I didn't expect.
I am VERY impressed With this site . I am very disappointed with Kitchenaid. I paid more for this mixer than I paid for my first car especially when you ad in the attachments. I was mixing dough when I saw what looked like Small metal shavings in the dough... Then I heard a clacking sound so I turned off the machine and cussed...I got the screw driver and took off the top and was really surprised that on a machine that retails for over $550.00 dollars that the gear housing is PLASTIC...And this one had a crack down the side... So I took my trusty Phillips #2 and removed the housing to see that the front Bearing was broken as well so I got on line to kitchenaid and they are determined to continue the process of Shafting you and I with the prices of thier made to fail (Quickly) parts and lubricants.. Thank God for PartSelect. I got a better housing for half the money as well as a Bearing. Now I wish this were the end but remember I said that there was metal shavings in my dough? Well since I was going to have to replace the lube anyway I took apart the planetary gear as well and found that it had been shaving metal from the underside of the upper main housing .. After cleaning I checked and the lower bushing wasn't seated so it had been doing this since I bought it and I didn't know.. So I got a C Clamp and pressed it to where the thing should have been to begin with. If you are going to be working on the thing I suggest you tear it down completely and clean It thoroughly and inspect EVERYTHING closely... I have been eating metal shavings for who knows how long...
At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.
The coating was chipping off of the original Flat Beater
All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.
speed control went. The beater would fly in any setting
I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.
Speed control switch kept getting stuck and we had to use the dough hook to move the control back and forth
I ordered the switch control. Opened up the top part of the mixer using a Philips screwdriver. Then I unscrewed all the screws that connected the old part. Disconnected the wires, connected them to the new panel , screwed everything back together and i was done. It was that easy.
Took it apart, found stripped gears, a common problem. Reviewed parts diagram on your website. Got the parts, reviewed the diagram, removed defective parts, used retaining ring pliers. put it back together, put new grease in, tried it out. Very easy fix