Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
over filling
no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!
The plastic door strike/catch had become brittle and broken off inside the door on a front loading washer.
There were only two screws that held the door strike/catch in place. I had to fish out the broken plastic piece with a pair of hemostats. The only difficult part about changing the new piece was that I had to find someone with the correct screwdriver to use since it was not a standara screwdriver. Luckily I live next door to a mechanic and borrowed his. The two screws came off easilty and I was able to replace it in 2 minutes. I was thrilled that the part that I ordered arrived the next day.
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
Bearings in pump were lose and the washer was not pumping the water out
First I pulled the front panel on the washer off, than I unplugged the wires to the pump, took the two screws out that hold the pump, took the two hose clamps off and took it out. To replace I did the reverse.
took off 2 screws and 2 hose clamps put in new part. Put srews and clamp back on less than ten minutes. total cost with shipping $62.00. repair person wanted $265.00.
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
Pulled the back off and it was right there. Hardest part was to get the belt all the way around the drive wheel on the washer tub. Found out that it wasn't just the belt. It is the shock absorbers that probably broke the belt, even though the belt was probably well over 15 years old. The bouncing and banging because of the absorbers being bad probably had something to do with the belt eventually breaking. Now, we need to replace the shock absorbers.A big thing to remember about the belt install....clean the drive wheel real good!!!
Spring broke and front loading washer made loud noise when it went into spin cycle.
Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.
The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.