Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
latch on detergent assembly broken off
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
i removed the screw holding the drain pump to the wire that held the pump to the dishwasher frame, i then unscrewed the hose clamps that connected the pump to the drain hose and the other part of the dishwasher i disconnected the wires , put the other pump into place wired it up and now my dishwasher is as good as new .
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
It makes a beeping sound in the middle of the dishwashing.
Remove the screws from the door and replace the switch interlock and door latch.
The problem is fixed and the dishwasher works fine so far (about three weeks) now.
The source of the problem looks more like the door latch because I use to push the door in to get it going before I replace the parts.
The video I received via email that show the how to do it was very helpful.
————- Update after more than month. (12/30/2020) The problem still persists. However I have a possible solution for it that doesn’t require any parts at all. The entire dishwasher is tilted backward. As the washing started and the water pileup in the bottoms of the dishwasher, it pull the entire dishwasher back work causing the switch interlock to release (open the relay causing the door open been sounds).
Level the dishwasher so that it doesn’t tilt backwards and this should fix the issue. I will post the latest after a month. If you need more info I can send a picture to describe the issue more clearly. ————————— Update 01-06-2021 The problem still persists. The above theory I had was wrong and didn’t make any difference.
However, I have a permanent solution but it may not be ideal for most people ??. The relay that get close/open when the door is close/open is now always CLOSED. To start the dishwasher just press start and make sure you don’t open the door while the dishwasher is running. It will not stop. I am sorry and I know it’s not a good solution but it’s kind of funny.
The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!
Old lower dish rack had rusted in places due to some of the protective coating wearing off.
It is extremely easy. Just take out the old lower rack and slide in the new rack. Remove the silverware holder from the old rack and insert it into the new rack.
As per instructions, any one that can read and use basic hand tools could do it. Very nice color instructions. BTW, this was an excellent value, $20 cheaper than two of the other parts houses I checked. Super fast shipping
at start of the wash cycle did not take in any water
very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.
The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.