Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Compressor making excessive noise
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.
Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line which we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.
Refrigerator door wouldn't close on it's own anymore
All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back on and put the screws back in on the top hinge of the refrigerator door. Works great now!
1, Removed heavy items from door bottom two shelves. 2. With door closed, prop up door with 2x4 boards and wood shim to support door weight. 3. With nut driver, wrench or socket wrench remove lower door hindge. 4. Removed worn plastic door cams and shim. 5. Install new door cams and shim. 6. Install lower door hindge and lubricate cams with silicone grease. 7. Remove wood bracing.
Unit would freeze then defrost but not go back into freezing again untill I moved the thermostat
Turn off power .Remove the control knobs and pry off the front panel ,it just snaps on,Take out two screws holding the control panel Take out the two screws holding the control to the base of the panel to get at the two screws holding the control to the bracket. Ther are screws holding the covers over the thermostat tube. Then pull out the tubbe and remove the plastic cover on the old control and place it on the new control tube. Then route the new tube into the snaps be careful to not make ant sharp bends in tubing.When that is done fasten the control to the bracket and fasten the bracket to the panel.Replace covers over tube to hide it and keep from damaging it when putting things in fridge.. Mount the conrol bracket back to the fridge and replace snap on cover. Plug in electric.
Our refrigerator failed to cool in stages, finally quitting to cool or run.
First, after re-reading your descriptions here on your site ( it took clues from each of them) I unplugged the refrigerator and began on the only day my husband was out of town. The two selector knobs came off easily fingers only. The plate came off with only a slight prying with a screwdriver (it is intended to snap off this way). Loosening the screws and removing them in order to remember which order they returned proved to be a challenge. After disassembly, pulling the thermostat out of the tubing and replacing it with the new one without bending it was hard to do also. The refrigerator runs like new, and may run another eleven years! Thanks!
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!
I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.
