Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.
light would stay on all the time saying burner was on although it wasn`t
unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all
The element on my 20+ year old Jenn Zaire oven had broken in two...
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making my problem, no problem at all!
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done! recieved my replacement part the next day after ordering
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John Johnny on the Spot Home Repairs Fishers, Indiana 317-997-3600
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done
